美国电影禁忌乱偷DVD版高清,特级毛片a级毛片免费播放,亚洲一区二区三区影院,亚洲AV无码专区在线观看下载

?

常州市衡正電子儀器有限公司是一家集軟件開發、制造、銷售、服務于一體的科技型現代化企業。
掃描手機二維碼
掃描微信二維碼
13861223798

新聞中心

NEWS CENTER

網站公告:測試信息來自互聯網,若涉及侵權,請聯系我們刪除! 您當前所在位置:首頁 > News > company news > 正文返回

Dial viscometer Notes on installing and unloading the rotor

更新時間:2017-04-20 10:31:02點擊次數:3797次字號:T|T
The operator must be careful when installing or unloading the rotor. All viscometers can measure extremely small torques due to the rotation of the rotor within the sample fluid. This requires that the friction inside the instrument be kept at a minimum.
The operator must be careful when installing or unloading the rotor. All viscometers can measure extremely small torques due to the rotation of the rotor within the sample fluid. This requires that the friction inside the instrument be kept at a minimum. The instrument is supported by a pivot system and a gemstone bearing system, with almost no friction, as shown on the right. The support mechanism is in the pivot cup just above the position where the rotor is installed.

When the rotor is installed or unloaded, any downward force or lateral movement will cause great wear to the support system.
When you tighten or loosen the rotor, the correct way to install and unload the rotor is to gently lift the nut at the rotor and then lift it firmly. Also remember that the rotor is fixed from the opposite direction of the thread (left hand).
Similar to the precautions described above can ensure that your viscometer or rheometer can provide reliable service for a long time.
Vibration check, there is a quick check to determine the pivot point of your instrument and the status of the gem support system, you can follow the following steps:
1, do not install the rotor in the case, to ensure that the instrument zero scale in the reading window.
2, observe the red pointer just stopped at the zero indicator line.
3. Lift the nut at the rotor and rotate until the indicator reaches + 20%.
4, put down the nut at the rotor and let go, observe the red pointer until the vibration stops. Record the approximate number of vibrations and the time of vibration.
5, red pointer at this time should still stop at the zero indicator line mark. If not stopped at zero, indicating that the instrument's support system has been a certain damage. Continue to repeat the calibration procedure, if the calibration check falls outside the allowable range, call the local office or call the manufacturer directly to tell you the results and get the service for your instrument.
(編輯:HengZheng)
0 條評論
不想登錄?直接點擊發布即可作為游客留言。

新聞中心列表

公司新聞
行業資訊

新聞推薦

電子天平使用應具備的基本知識

電子密度天平計量檢定項目

在日常的周期檢定和常規的產品質量檢查中,一般需要檢定以下幾項內容...

JA系列電子天平選購應該注意哪...

JA系列電子天平對操作人員的兼容性和對操作環境的耐受能力。

如何正確使用FA系列電子天平?

準備將FA系列電子天平放在穩定的工作臺上,避免振動,氣流、陽光直...

FA系列電子天平使用的注意事項

電子天平如何測量固體密度

鹵素水分測定儀操作過程

聯系我們

地址:江蘇省常州市鐘樓區龍城大道2188號新閘科技園

聯系人:查小姐
郵編:213000
電話:0519-83263587
傳真:0519-83268313
網址:http://n4636.cn/

聯系我們
地址:常州市鐘樓區龍城大道2188號新閘科技園10棟313
聯系人:查小姐
電話:0519-83263587
傳真:0519-83268313
網址:http://www.czhz17.com
關注衡正
Copyright ? 2017 - 2024 All Rights Reserved 常州市衡正電子儀器有限公司 版權所有  蘇ICP備17024635號 技術支持:冉冉科技 網站地圖